How To Set Up Enbrighten Smart Plug

MANUAL

55249
ZW4106
Plug-in
Smart Switch

Scan QR code or visit https://byjasco.com/55249i

Exercise Non Return THIS PRODUCT TO THE Store

If you take any problems or questions, contact our U.S.-based Consumer Care at 1-800-654-8483, option ane, Monday–Friday, 7 AM–8 PM Primal Time. For the most up-to-date product support, accessories, electronic (PDF) format manuals, and more, visit www.byjasco.com/support.

• No user-serviceable parts in this unit of measurement.

i.

Getting to know your new Z-Moving ridge device
Total load capacity for both outlets must not exceed 600W (5A) incandescent, 1800W (15A) resistive, or 1/2HP motor.

• Two Z-Wave controlled Air-conditioning outlets for LED, CFL, incandescent, and halogen lights too equally small appliances
• Remote ON/OFF control via the Z-Wave controller
• Manual ON/OFF control with the height-mounted button button
• Infinite-efficient design
• Does not block the lower outlet when plugged into the upper outlet of a duplex wall receptacle (assumes the duplex receptacle is mounted with the footing pin down)
• Plugs and cords for continued devices route to the side allowing close placement of furniture
• Grounded 3-wire power connection for safe
• This Z-Wave smart switch has advanced features that allow y'all to customize your feel — these features can merely exist adjusted by a Z-Wave enabled controller that supports the Z-Wave configuration command class. For a complete list of adjustable configurations, visit www.ezzwave.com/config

2.

A. Z-Wave controlled outlets
Both outlets are controlled together and can remotely
plow ON/OFF the continued device(s)
B. Manual/program button
Single printing — turn the continued device(s) ON/OFF
Unmarried press — add or remove in Z-Moving ridge network
C. Wheel LED light
The LED acts as a guiding light or status indicator.
How to bike through options: Press the programme button
10 times rapidly.

1. LED is ON when the load is ON (indicates the switch is ON) (default)
2. LED is ON when the load is OFF (guide light in the night)
3. LED is always OFF
4. LED is always ON

•  Both outlets tin can simply be controlled together. Cannot be independently controlled.

Calculation your device to a Z-Wave network:

1. Follow the instructions for your Z-Wave certified controller to add together the smart switch to the Z-Wave network.
2. Once the controller is prepare to add together your smart switch, printing and release the manual/programme push button on the smart switch. You lot take consummate control to turn your device(s) ON/OFF co-ordinate to groups, scenes, schedules, and interactive automation programmed past your controller. If your Z-Wave certified controller features remote access,
   you can command your device(s) from your mobile devices. If prompted by the controller to enter the S2 security lawmaking, refer to the QR code/security number on the side of the box or the QR code characterization on the product (see Figure 1). Enter the v-digit PIN code.

Figure 1:

https://byjasco.com/HEP-ET/20000-99999/39339

Please reference the controller's transmission for instructions.
To remove and reset the device:

1. Follow the instructions for your Z-Moving ridge certified controller to remove a smart switch from the Z-Moving ridge network.
2. Once the controller is set up to remove your smart switch, printing and release the manual/program button onthe smart switch.

To render your switch to mill defaults:

1. If plugged in, unplug the smart switch from the receptacle.
2. Printing and concord the program button for at to the lowest degree three seconds while you plug the smart switch into a receptacle.

NOTE: This should only be used in the upshot your network's principal controller is missing or otherwise inoperable.
Notation: SmartStart enabled products can be added into a Z-Wave network by scanning the QR code on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of existence switched on in the network vicinity.

Z-WAVE INTEROPERABILITY
This product tin can exist included and operated in whatsoever Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-bombardment
operated nodes within the network will deed as repeaters regardless of vendor to increase the reliability of the network.

This device supports Association Command Course (3 Groups)

• Association Grouping 1 supports Lifeline, Switch Binary Written report
• Association Group ii supports Bones Fix and is controlled with the local load
• Association Group iii supports Bones Set and is controlled by double-pressing the button
• Each Association Group supports 5 total nodes

Alarm

Adventure OF Burn
Run a risk OF Electrical SHOCK
RISK OF BURNS

TO REDUCE THE RISK OF Electrical SHOCK, THE Production HAS A GROUNDING PLUG THAT HAS A 3rd (GROUNDING) PIN. THIS PLUG Volition Simply FIT INTO A GROUNDING Ability OUTLET. IF THE PLUG DOES Non FIT INTO THE OUTLET, CONTACT A QUALIFIED ELECTRICIAN TO INSTALL THE PROPER OUTLET. Do Non Change THE PLUGIN ANY Fashion.

Controlling APPLIANCES
CAUTION: TO REDUCE THE Run a risk OF OVERHEATING AND POSSIBLE Harm TO OTHER EQUIPMENT

• DO NOT EXCEED RATINGS
• DO Not USE TO Control ANY DEVICE WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (Estrus LAMP, SUN LAMP, ETC.)

WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states practise not allow limitations on how long an unsaid warranty lasts or permit the exclusion or limitation of incidental or consequential harm, so the higher up limitations may not employ to you. This warranty gives you specific rights, and you may besides have other rights which vary from land to land. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (selection 1) between 7 AM – 8 PM, M-F, Key Time, or www.byjasco.com if the unit of measurement should prove lacking inside the warranty period.

SPECIFICATIONS

Power: 120VAC, 60Hz
Point frequency: 908.4/916MHz
Total maximum load for both Z-Wave controlled outlets:
600W (5A) tungsten, 1/2HP motor or 1800W (15A) resistive
Range: Upwardly to 150ft. line of sight between the wireless controller and the closest Z-Wave receiver module
Operating temperature range: 32-104° F (0-twoscore° C) For indoor use only
Specifications subject area to alter without find due to continuing product improvement

FCC

This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standards. Functioning is field of study to the following two conditions:
(1) this device may not crusade harmful interference, and (2) this device must take any interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, in that location is no guarantee interference will not occur in a
item installation. If this equipment does cause harmful interference to radio or television reception, which can be adamant by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more than of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from which the receiver is connected.
— Consult the dealer or an experienced radio/Television technician for help.
Of import note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Whatever change to the antenna or the device could consequence in the device exceeding the RF exposure requirements and void user's authority to operate the device.

Documents / Resources

Source: https://manuals.plus/enbrighten/plug-in-smart-switch-manual

Share this post